Convenience Store Energy Costs: Refrigeration, Lighting and HVAC Checks an Owner Can Make

Refrigeration is the largest use of electricity in U.S. food sales buildings, the federal survey category that includes convenience stores, so the work of cutting a store’s electric bill starts at the cooler doors, the coils and the walk-in.

The figures come from the U.S. Energy Information Administration’s 2018 buildings survey and from ENERGY STAR and Department of Energy documents read on 11 November 2026. Each savings figure is the source’s own estimate; a store’s result depends on its equipment, hours, climate and electricity rate.

Where the electricity goes in a food store

Table E5 of the Energy Information Administration’s 2018 Commercial Buildings Energy Consumption Survey, released in December 2022, estimates that food sales buildings used 54 billion kWh of electricity in 2018 and assigns 26 billion kWh of it to refrigeration. Lighting and ventilation come next at 4 billion kWh each, then space heating, cooling and cooking at 2 billion kWh each. Water heating and office equipment round to zero in the table’s units, and the table withholds the computing and other columns for food sales. Refrigeration is a little under half of the total by our arithmetic. No later survey year appeared on EIA’s survey page on 11 November 2026.

EIA’s building type definitions describe food sales as “Buildings used for retail or wholesale of food.” and give three examples: grocery store or food market, convenience store (with or without a gas station), and bakery. The category puts supermarkets and corner stores in one group, so its figures are group totals and averages.

In the survey’s Table C14, food sales buildings used 53.3 kWh of electricity per square foot in 2018, against 12.6 kWh for all commercial buildings, and spent $5.27 per square foot on electricity, against $1.25.

ENERGY STAR’s page for convenience stores uses a different measure, total energy, and a ceiling phrase: “For convenience stores, refrigeration may use up to 40 percent of the property’s total energy.” The page gives no year or data source for the figure.

Start with twelve months of bills

The ENERGY STAR convenience store page starts with benchmarking from the utility bill. Our first step is to lay out twelve months of electric bills and note, for each month, the kWh used, the total charge, any demand charge and the rate class.

ENERGY STAR’s Energy and Water Efficiency Checklist for Convenience Stores, a nine-page PDF from 2024, adds two tips about the bill itself. One is an all-utility audit that looks for billing errors and proper rate classification. The other is load shedding during the utility’s peak-demand time of day, to avoid demand charges. The tip closes: “Ask your utility about programs and financial incentives for customers to avoid contributing to peak demand.”

The checklist also describes Portfolio Manager, a free online tool that gives a store an ENERGY STAR score from 1 to 100 against other U.S. convenience stores.

NRS’s guide to reading a profit and loss statement lists utilities among a store’s operating expenses and advises tracking each of those lines as a percentage of revenue over time, asking of each whether it is growing faster than revenue.

Refrigeration habits and maintenance checks

The ENERGY STAR convenience store page lists five refrigeration tips. One is to buy ENERGY STAR certified refrigerators and freezers; the other four are habits and maintenance:

  • Doors. “Keep the doors of all refrigeration and freezer units shut as much as possible as repeated fluctuations in temperature will damage food quality and cost money.”
  • Settings. “If the temperature is set lower than necessary, you are probably wasting energy. The most common recommended settings are between -14° and -8° Fahrenheit for freezers and between 35° and 38° Fahrenheit for refrigerators.”
  • Coils. “Clean the cooling coils on the backs of all units. Over time, dirt accumulation impairs proper heat transfer and lowers the efficiency and capacity of refrigerators.” The tip adds that ice on the coils should be removed as well.
  • Door seals. “If you can easily slide a dollar bill into the seal, have the seal adjusted.”

ENERGY STAR’s checklist for convenience stores advises replacing a gasket that fails the test and cleaning gaskets regularly with soapy water. It adds: “Install strip curtains and keep condenser and evaporator coils clean.” And: “Alcohol and soft drinks don’t have to be chilled to the lower temperatures required for perishable foods.”

In our view staff can make most of these checks, with three cautions. A temperature setting for food answers first to the cold-holding limit the health inspector enforces, so confirm that limit before raising any setting. Coil cleaning follows the manufacturer’s manual. Coils and condensers on a roof or behind a locked panel, and a seal that needs adjusting, go to the refrigeration technician.

NRS’s guide to weather-driven demand makes two of these checks part of heat-wave preparation: checking refrigeration unit performance and door gasket seals before a heat advisory.

Refrigeration upgrades to price with a contractor

The refrigeration list in the ENERGY STAR checklist also names controls and parts. Four of them, as a partial list:

  • Anti-sweat controls. “Consider installing anti-sweat controls to monitor both humidity and temperature to activate heaters in cooler and freezer doors only when needed to prevent condensation.”
  • Defrost controls. Controls that use sensors to tell when evaporator coils need defrosting and use defrost energy only then.
  • Fan motors. Electronically commutated motors.
  • Case lighting. “Check whether refrigerated case lighting is LED.”

A guide to retrofitting open refrigerated display cases with doors, prepared for the U.S. Department of Energy’s Better Buildings Alliance, published in November 2012 and updated in June 2013, puts numbers on two of those items. On evaporator fan motors, it says permanent split capacitor motors and electronically commutated motors “can reduce fan motor energy consumption on the order of 40% and 70%, respectively, when compared to shaded-pole motors (SPMs).” On LED fixtures replacing T8 fluorescent fixtures in cases: “These fixtures have the potential to reduce lighting energy consumption by a factor on the order of 70%, while maintaining the level of product illumination needed for proper merchandising and product display.”

The guide’s subject is retrofitting open refrigerated supermarket display cases with transparent doors, and its introduction says open cases are commonly used in supermarkets, multi-line retail stores and convenience stores. Installing doors on previously open cases, it says, brings a large decrease in the heat load the refrigeration system must remove, “on the order of 50-80%”. That figure measures heat load, and the guide gives no figure for a self-contained plug-in case. It warns that the refrigeration system has to be adjusted to the smaller load, and that a poorly performed retrofit “can yield energy savings far below those originally anticipated by the end user at the beginning of the retrofit process.” It adds: “A qualified refrigeration engineer or firm should always be contracted to oversee any retrofit project.”

The walk-in cooler: a parts list from the federal standard

10 CFR 431.306, read as it stands on 11 November 2026, gives an owner a parts list for the walk-in. Paragraph (a) applies to each walk-in cooler or walk-in freezer manufactured on or after January 1, 2009. Five of its seven items are things an owner can see or ask about, grouped here in four lines:

  • Automatic door closers, except on doors wider than 3 feet 9 inches or taller than 7 feet.
  • Strip doors, spring hinged doors, or another method of minimizing infiltration when doors are open.
  • Electronically commutated or 3-phase evaporator fan motors (for motors under 1 horsepower and less than 460 volts), and electronically commutated, permanent split capacitor-type or 3-phase condenser fan motors (under 1 horsepower).
  • Interior light sources of 40 lumens per watt or more, including ballast losses, or less efficient ones used with a timer or device that turns the lights off within 15 minutes of when the walk-in is not occupied by people.

The other two items set minimum insulation values, and paragraphs (b) through (e) are not summarized here. The section is written as a standard for walk-ins as manufactured; the Department of Energy’s walk-in coolers and freezers page says manufacturers have been required to comply with its standards for walk-ins since 2009. Who counts as the manufacturer of a walk-in assembled on site is a question for the contractor and the Department. For an owner, the list works as questions for the refrigeration contractor.

Lighting: lamps, controls and day-burners

The ENERGY STAR convenience store page says ENERGY STAR-qualified LED lighting “uses up to 90% less energy than incandescent lighting, saving on operating expenses.” The page gives no energy figure against fluorescent tubes, the comparison a store lit by tubes needs from a lighting contractor.

ENERGY STAR’s checklist is more specific about tubes: “Replace T12 fluorescents and obsolete magnetic ballasts, ideally with tubular LEDs (TLEDs). Retain existing T8s or T5s with electronic ballasts through their useful life.” Three of its other lighting checks, as a partial list:

  • Walk the store in the daytime and the evening for lights left on in unoccupied spaces, including offices, restrooms, storage and hallways.
  • Look during the day for what the checklist calls day-burners: exterior and parking lot lights that should be on only at night and have a failed or dirty light sensor.
  • Consider occupancy or motion sensors for low-traffic areas, and timers or daylight sensors that turn off exterior and parking lot lights during the day.

Heating and cooling: filters, tune-ups and thermostats

The ENERGY STAR convenience store page gives four heating and cooling tips, in this order:

  1. Filter. “Check your filter every month, especially during heavy use months (winter and summer). If the filter looks dirty after a month, change it. At a minimum, change the filter every three months.”
  2. Tune-up. The tip is headed “Tune up your HVAC equipment yearly.”
  3. Thermostat. Install a programmable thermostat. “Rooms that have minimal traffic (such as stock rooms and warehouses) should be kept cooler in the winter and warmer in the summer.”
  4. Ducts. “Sealing and insulating ducts can improve the efficiency of your heating and cooling system by as much as 20 percent and sometimes much more.”

The checklist for convenience stores asks for regular maintenance by qualified staff or under an annual maintenance contract, with tune-ups before both the heating and the cooling season. It lists four things everyone can help with: replacing filters, keeping supply and return registers clear, keeping electronics and heat sources away from thermostats, and using window shades or curtains to block excess heat. On replacement it is blunt: “Do not buy a larger system than you need.”

Food service, ice, vending and plug loads

For a store with a food program, the kitchen list in ENERGY STAR’s checklist includes this line: “Avoid placing heating equipment near cooling equipment.” Its plug-load list says to turn off equipment left on overnight unnecessarily.

ENERGY STAR’s commercial ice makers page gives figures for two types: certified batch-type ice makers “save businesses 700 kWh and $150 annually and $1,200 over the product’s lifetime on utility bills”, and continuous-type ones 1,350 kWh and $170 annually and $1,300 over the lifetime. The vending machines page says: “ENERGY STAR certified refrigerated beverage vending machines are on average 9% more efficient and save about 1,000 kWh annually.” On ownership: “Generally the operator owns the vending machines but you may have some opportunities to work with them to get energy efficient machines that will cost you less to operate.”

NRS’s guide to earning revenue from unused store space lists who bears the cost of power consumption among the key terms to review in a vending commission agreement. Our advice is to ask the same question about any cooler or freezer a supplier places in the store.

Replacing equipment: labels, rebates and payback

ENERGY STAR’s commercial refrigerators and freezers page says certified models are on average 20 percent more energy efficient than standard models. Its annual savings figures for four product types, in its order (it also gives lifetime figures):

  • Solid door refrigerators: 325 kWh and more than $40 annually.
  • Glass door refrigerators: 370 kWh and nearly $50 annually.
  • Solid door freezers: 80 kWh and more than $10 annually.
  • Glass door freezers: 900 kWh and more than $110 annually.

The page states no electricity rate and no date for the dollar figures, so the kWh figures are the ones to carry into a store’s own arithmetic. Its list of ineligible products includes open air units and remote condensing equipment, so an open air merchandiser has no labeled model to compare against.

On rebates, the product page says: “Many utilities also offer rebates to offset the purchase price of ENERGY STAR equipment.” ENERGY STAR’s Rebate Finder searches by ZIP code. Our advice is to ask the utility whether an application has to be approved before the purchase.

Simple payback, in years, is our own arithmetic: the net cost of a project divided by the money it saves in a year. Net cost is the installed cost on a written quote, less any rebate the utility has confirmed in writing. Annual savings are the kWh saved per year, from the contractor’s estimate or the label’s figure, multiplied by the store’s own rate: the energy charges on a recent bill divided by the kWh billed. Leave demand charges out unless the contractor shows the project lowers the store’s peak.

Illustration with the sources’ own figures: ENERGY STAR’s 900 kWh a year for a certified glass door freezer, at the 2018 average of $0.099 per kWh for food sales buildings in EIA’s Table C14, a rate eight years old, comes to $89.10 a year. ENERGY STAR’s page puts the same 900 kWh at more than $110, implying a higher rate.

Simple payback leaves out financing costs, maintenance savings and the tax treatment of equipment; your accountant can add those.

The Energy Walk card: a one-page tool

Ten checks, by equipment. ES marks an interval or source from the ENERGY STAR page or checklist; intervals marked NRS, and the Who column, are our suggestion.

EquipmentWhat to look atHow oftenWhoSource 
Electric billskWh, total charge, demand charge, rate classEach bill (NRS)OwnerES page, checklist
Cooler and freezer doors, gasketsShut; strip curtain in place; dollar-bill test; gasket cleanEvery shift for doors; monthly for gaskets (NRS)Shift leadES page, checklist
Temperature settingsNo lower than necessary; health code limit first (our advice)Weekly (NRS)ManagerES page
CoilsDirt, dust and iceQuarterly (NRS)Staff; technicianES page, checklist
Anti-sweat heaters, defrost, fan motors, case lightsControls fitted; motor type; LED or fluorescentYearly service visit (NRS)Refrigeration contractorES checklist; DOE guide
Walk-inDoor closer; strip curtain; fan motor type; efficient lights, or a timerYearly service visit (NRS)Owner and contractor10 CFR 431.306(a)
Open casesA quote for doors, with system adjustmentAt a remodel (NRS)Refrigeration engineer or firmDOE guide
LampsT12 tubes, magnetic ballasts; lights on in empty rooms or in daylightMonthly (NRS)Owner or shift leadES checklist
HVACFilter; contractor tune-upFilter: check monthly, change at least every three months; tune-up yearly (ES)Staff; HVAC contractorES page, checklist
Kitchen, ice and vendingOff when not in use; heat away from cooling; who pays for powerDaily; at vending contract renewal (NRS)Staff; ownerES checklist, vending page; NRS guide

Frequently asked questions

What uses the most electricity in a convenience store?

Refrigeration is the largest electricity use in food sales buildings as a group, and neither source read here ranks end uses for convenience stores alone. EIA’s Table E5 assigns 26 of the 54 billion kWh those buildings used in 2018 to refrigeration, and the category also covers grocery stores and bakeries. ENERGY STAR’s convenience store page says only that refrigeration may use up to 40 percent of a convenience store’s total energy.

Should I put doors on an open refrigerated case?

Get a quote from a qualified refrigeration engineer or firm before deciding. The retrofit guide prepared for the Department of Energy in 2012 and updated in 2013 addresses supermarket display cases. It reports a large decrease in heat load for open cases fitted with doors, gives no figure for a plug-in case, and warns that a poorly performed retrofit can save far less than expected.

How often should the HVAC filter be changed?

ENERGY STAR’s convenience store page says to check it every month, change it if it looks dirty, and change it at least every three months.

Key takeaways

Refrigeration comes first in food sales buildings. EIA’s 2018 survey assigns it 26 of their 54 billion kWh, per Table E5; the category covers grocery stores and bakeries as well as convenience stores.

ENERGY STAR’s convenience store page gives four refrigeration habit and maintenance tips: doors kept shut, settings no lower than necessary, clean coils and tight door seals. In our view staff can make most of these checks.

Controls, fan motors and case lighting are upgrades to price with a contractor, in our view. For doors on open cases, the guide prepared for the Department of Energy (2012, updated 2013), which addresses supermarket display cases, says a qualified refrigeration engineer or firm should always be contracted to oversee the retrofit.

Savings figures are estimates. Work out simple payback with a written quote, a confirmed rebate and the rate on your own bill.

arrow that scrolls the page to the top when clicked